Build Your Own PACE!
The Plankton, Aerosol, Cloud, ocean Ecosystem (PACE) spacecraft is designed to provide new insight into Earth's ocean and atmosphere. PACE will provide the first-ever global measurements to identify communities of microscopic algae that float in our ocean: phytoplankton. This will help us understand Earth's changing marine ecosystems, manage natural resources such as fisheries, and detect harmful algal blooms. Its atmospheric data will be used to study key issues such as air quality.
It usually takes years to build a satellite that can survive the extremes of space. This paper model replica of PACE has five parts plus an optional 'Hinge'. Just like NASA, you will create the final spacecraft model by assembling the parts together...but in a tiny fraction of the time!
It usually takes years to build a satellite that can survive the extremes of space. This paper model replica of PACE has five parts plus an optional 'Hinge'. Just like NASA, you will create the final spacecraft model by assembling the parts together...but in a tiny fraction of the time!
![](/images/paper_model_materials.png)
Instructions and Templates
For best results, print templates on cardstock.
The central part of PACE is called a "bus." It serves as the hub for the spacecraft, providing places to mount science instruments, solar array, communications equipment, etc. It also houses electronic systems that distribute power and information needed to operate the spacecraft.
DIRECTIONS
- Cut solid lines, including red circle and two small red notches.
- Cut out the "Bus End Piece" and save until later.
- Fold along all dashed lines, creating a cube shape.
- Glue tabs marked "1" to corresponding inner walls of the Bus, leaving the top open until the Beam and Solar Array are built.
An array of solar panels are needed to power PACE. Before launch, the solar array is folded and then unfurls in orbit. For this model, the Beam is a single piece that connects the Solar Array to the Bus.
DIRECTIONS
- Cut out the Beam. (If using thin paper, shorten or omit red notches.)
- Fold along the long dashed lines. Leave ends unfolded.
- Glue along the green dots to form a rectangular piece.
- Cut out the Solar Array and its "End Piece." Fold along all lines.
- Glue tabs marked "1" to long edge of the Solar Array.
- Following directions printed on the Beam, place it in the Solar Array.
- Glue Solar Array tabs marked "2."
- Fold back the ends of the Beam oriented away from the Bus.
- Glue the "Solar Array End Piece" over the Beam's folded end.
- Insert the Beam's other end in the hole in the Bus. Fold back its ends.
- With the Beam sitting in the notch, glue the top of the Bus closed.
- Glue the "Bus End Piece" on top of the Beam's folded end.
See how it's done!
A Radiator Shield blocks out nearly 80% of Earth's energy.
DIRECTIONS
- Note the direction of red arrows and cut out the Radiator Shield.
- Fold along all lines. There is one dotted line ("valley fold").
- Glue tabs marked "1" to short sides of triangles (per red arrows).
- Push folded paper into the Radiator Shield, over the tab marked "2."
- Glue the tab marked "2" to the bottom of the folded paper.
The Ocean Color Instrument (OCI) is designed to measure light at finer wavelength resolution than previous NASA sensors. Its spectrographs will split light down to 5 nanometers (5 one-billionths of a meter).
DIRECTIONS
- Cut out the OCI. Make all folds, including valley above spectrographs.
- Glue areas marked "1" to form rectangular solar calibration assembly. Glue tabs marked "2" to form the back of the OCI.
- Glue tabs marked "3" to form the data, control & interface units.
- Glue tabs marked "4". Each tab can be pinched closed separately. Be careful to maintain the angle along the edge of the spectrographs.
- Glue tabs marked "5" to finish the front side of the OCI.
- Glue areas marked "6" to finish the bottom and the port side (i.e., side facing left when looking along PACE's flight direction).
- Finish your PACE paper model by doing the following:
- Glue Radiator Shield to OCI. Be sure to align the two white boxes.
- Glue OCI/Radiator Shield to Bus (or optional "Hinge," see below).
- Slightly bend down the Beam (see image at top left).
See how it's done!
Estimated completion time of 90 minutes.