About CEN
The European Committee for Standardization is one of three European Standardization Organizations (together with CENELEC and ETSI) that have been officially recognized by the European Union and by the European Free Trade Association (EFTA) as being responsible for developing and defining voluntary standards at European level.
- |
Project
| Reference | EN ISO 5167-6:2022 |
|---|---|
| Title | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 6: Wedge meters (ISO 5167-6:2022) |
| Work Item Number | CSF05037 |
| Abstract/Scope | This document specifies the geometry and method of use (installation and operating conditions) of wedge meters when they are inserted in a conduit running full to determine the flow rate of the fluid flowing in the conduit. NOTE 1 As the uncertainty of an uncalibrated wedge meter can be too large for a particular application, it could be deemed essential to calibrate the flow meter according to Clause 7. This document gives requirements for calibration which, if applied, are for use over the calibrated Reynolds number range. Clause 7 could also be useful guidance for calibration of meters of similar design but which fall outside the scope of this document. It also provides background information for calculating the flow rate and is applicable in conjunction with the requirements given in ISO 5167‑1. This document is applicable only to wedge meters in which the flow remains subsonic throughout the measuring section and where the fluid can be considered as single-phase. Uncalibrated wedge meters can only be used within specified limits of pipe size, roughness, β (or wedge ratio) and Reynolds number. It is not applicable to the measurement of pulsating flow. It does not cover the use of uncalibrated wedge meters in pipes whose internal diameter is less than 50 mm or more than 600 mm, or where the pipe Reynolds numbers are below 1 × 104. NOTE 2 A wedge meter has a primary element which consists of a wedge-shaped restriction of a specific geometry. Alternative designs of wedge meters are available; however, at the time of writing there is insufficient data to fully characterize these devices, and therefore these meters are calibrated in accordance with Clause 7. |
| Status |
Published
|
| Reference Document |
ISO 5167-6:2022 (EQV)
|
| date of Availability (DAV) | 2022-11-02 |
| ICS | 17.120.10 - Flow in closed conduits |
| A-Deviation(s) | |
| Special National Condition(s) |
Legal
| Directive(s) | |
|---|---|
| Mandate(s) | |
| Citation in OJEU |
Implementation Dates
| date of Ratification (DOR) (1) | 2022-09-25 |
|---|---|
| date of Availability (DAV) (2) | 2022-11-02 |
| date of Announcement (DOA) (3) | 2023-02-28 |
| date of Publication (DOP) (4) | 2023-05-31 |
| date of Withdrawal (DOW) (5) | 2023-05-31 |
Relations
| Supersedes | EN ISO 5167-6:2019 |
|---|---|
| Superseded by | |
| Normative reference (6) | |
| Sales Points |
|
(1) Date of ratification (dor) date when the Technical Board notes the approval of an EN (and HD for CENELEC), from which time the standard may be said to be approved
(2) Date of availability (dav) date when the definitive text in the official language versions of an approved CEN/CENELEC publication is distributed by the Central Secretariat
(3) Date of announcement (doa) latest date by which the existence of an EN (and HD for CENELEC), a TS or a CWA has to be announced at national level
(4) Date of publication (dop) latest date by which an EN has to be implemented at national level by publication of an identical national standard or by endorsement
(5) Date of withdrawal (dow) latest date by which national standards conflicting with an EN (and HD for CENELEC) have to be withdrawn
(6) This list of normative references is purely indicative. The only official list of normative reference is the list of the published standard.
In the case of undated standard, a link to the last dated version is provided.
In the case of series, a link to each standard identified in the series is provided.
We also invite you to check (via the website) whether corrigenda and/or amendments shall be read in conjunction with the main standard.