About CEN
The European Committee for Standardization is one of three European Standardization Organizations (together with CENELEC and ETSI) that have been officially recognized by the European Union and by the European Free Trade Association (EFTA) as being responsible for developing and defining voluntary standards at European level.
- |
Project
| Reference | EN ISO 8130-1:2019 |
|---|---|
| Title | Coating powders - Part 1: Determination of particle size distribution by sieving (ISO 8130-1:2019) |
| Work Item Number | 00139545 |
| Abstract/Scope | This document specifies a method for the determination of the particle size distribution of coating powders by sieve analysis. Particle size distributions with a maximum of less than 100 µm is determined by laser diffraction, ISO 8130‑13. This method is used especially for determining the oversize material or for the presence of contamination and can be used as a quality control procedure ("go"/"no go" test) by checking the amount retained on a single sieve. The following particle sizes are typical for coating powders, however the particle size can deviate depending on the application: — thin-film technology: 1 µm to 63 µm; — electrostatic coating: 10 µm to 200 µm; — fluidizing-bed method: 100 µm and above. NOTE Sieves with a mesh size smaller than 32 µm are not practical and are likely to become blind during use. |
| Status |
Published
|
| Reference Document |
ISO 8130-1:2019 (EQV)
|
| date of Availability (DAV) | 2019-05-08 |
| ICS | 87.040 - Paints and varnishes |
| A-Deviation(s) | |
| Special National Condition(s) |
Legal
| Directive(s) | |
|---|---|
| Mandate(s) | |
| Citation in OJEU |
Implementation Dates
| date of Ratification (DOR) (1) | 2019-03-08 |
|---|---|
| date of Availability (DAV) (2) | 2019-05-08 |
| date of Announcement (DOA) (3) | 2019-08-31 |
| date of Publication (DOP) (4) | 2019-11-30 |
| date of Withdrawal (DOW) (5) | 2019-11-30 |
Relations
| Supersedes | EN ISO 8130-1:2010 |
|---|---|
| Superseded by | |
| Normative reference (6) |
ISO 15528
ISO 3310-1 ISO 3310-2 ISO 565 ISO 8130-14 |
| Bibliographic references (7) | |
| Sales Points |
|
(1) Date of ratification (dor) date when the Technical Board notes the approval of an EN (and HD for CENELEC), from which time the standard may be said to be approved
(2) Date of availability (dav) date when the definitive text in the official language versions of an approved CEN/CENELEC publication is distributed by the Central Secretariat
(3) Date of announcement (doa) latest date by which the existence of an EN (and HD for CENELEC), a TS or a CWA has to be announced at national level
(4) Date of publication (dop) latest date by which an EN has to be implemented at national level by publication of an identical national standard or by endorsement
(5) Date of withdrawal (dow) latest date by which national standards conflicting with an EN (and HD for CENELEC) have to be withdrawn
(6) This list of normative references is purely indicative. The only official list of normative reference is the list of the published standard.
In the case of undated standard, a link to the last dated version is provided.
In the case of series, a link to each standard identified in the series is provided.
We also invite you to check (via the website) whether corrigenda and/or amendments shall be read in conjunction with the main standard.
(7) This list of bibliographic references, which is provided for homegrown standards only, is purely indicative and was retrieved automatically using available XML files. It is limited to publications that have been published in the XML format. For standards that are not homegrown, the corresponding international standard should be consulted.