About CEN
The European Committee for Standardization is one of three European Standardization Organizations (together with CENELEC and ETSI) that have been officially recognized by the European Union and by the European Free Trade Association (EFTA) as being responsible for developing and defining voluntary standards at European level.
- |
Project
| Reference | prEN 1453-1 rev |
|---|---|
| Title | Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system |
| Work Item Number | 00155999 |
| Abstract/Scope | This part of EN 1453 specifies the requirements for structured-wall unplasticized poly(vinyl chloride) (PVC U) pipes and the system intended to be used for soil and waste discharge applications (low and high temperature) inside buildings (application area code "B") NOTE 1 The intended use is reflected in the marking of products by "B". This part of EN 1453 is also applicable to structured-wall unplasticized poly(vinyl chloride) (PVC U) pipes, and the system intended for the following purposes: ventilating part of the pipework in association with discharge applications; rainwater pipework inside building. It also specifies the test parameters for the test methods referred to in this standard. NOTE 2 Single layer foamed PVC U pipes and spirally-formed PVC U pipes are not covered by this standard. This standard covers a range of nominal sizes and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. For external above ground application additional requirements depending on the climatic conditions should be agreed between the manufacturer and the user. NOTE 4 Pipes conforming to this standard are normally associated with fittings conforming to EN 1329 1. Pipes, fittings and components conforming to any of the product standards listed in Annex C can also be used with pipes conforming to this standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements in Table 11. NOTE 5 Joints and adhesives are considered to be part of the system as covered in the scope. NOTE 6 Products conforming to this standard may be submitted to national requirements on fire regulation. |
| Status |
Preliminary
|
| Reference Document | |
| date of Availability (DAV) | |
| ICS | |
| A-Deviation(s) | |
| Special National Condition(s) |
Legal
| Directive(s) | |
|---|---|
| Mandate(s) | |
| Citation in OJEU |
Implementation Dates
| date of Ratification (DOR) (1) | |
|---|---|
| date of Availability (DAV) (2) | |
| date of Announcement (DOA) (3) | |
| date of Publication (DOP) (4) | |
| date of Withdrawal (DOW) (5) |
Relations
| Supersedes | EN 1453-1:2017 |
|---|---|
| Superseded by |
(1) Date of ratification (dor) date when the Technical Board notes the approval of an EN (and HD for CENELEC), from which time the standard may be said to be approved
(2) Date of availability (dav) date when the definitive text in the official language versions of an approved CEN/CENELEC publication is distributed by the Central Secretariat
(3) Date of announcement (doa) latest date by which the existence of an EN (and HD for CENELEC), a TS or a CWA has to be announced at national level
(4) Date of publication (dop) latest date by which an EN has to be implemented at national level by publication of an identical national standard or by endorsement
(5) Date of withdrawal (dow) latest date by which national standards conflicting with an EN (and HD for CENELEC) have to be withdrawn
(6) This list of normative references is purely indicative. The only official list of normative reference is the list of the published standard.
In the case of undated standard, a link to the last dated version is provided.
In the case of series, a link to each standard identified in the series is provided.
We also invite you to check (via the website) whether corrigenda and/or amendments shall be read in conjunction with the main standard.