About CEN
The European Committee for Standardization is one of three European Standardization Organizations (together with CENELEC and ETSI) that have been officially recognized by the European Union and by the European Free Trade Association (EFTA) as being responsible for developing and defining voluntary standards at European level.
- |
Projet
| Reference | prEN 1451-1 rev |
|---|---|
| Title | Systèmes de canalisations en plastiques pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments Polypropylène (PP) Partie 1: Spécifications pour tubes, raccords et le système |
| Work Item Number | 00155A19 |
| Abstract/Scope | This part of EN 1451 specifies the requirements for solid-wall polypropylene (PP) pipes, fittings and the system intended for: — soil and waste discharge applications (low and high temperature) inside buildings (application area code “B”); — soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code “BD”). The intended use is reflected in the marking of products by “B” or “BD. NOTE 1 For use buried in the ground within the building structure are intended only those components marked with “BD”, with dimensions equal to or greater than 75 mm and nominal ring stiffness of at least SN4. This part of EN 1451 is also applicable to PP pipes and fittings and the system intended for the following purposes: — ventilating part of the pipework in association with discharge applications; — rainwater pipework within the building structure. It also specifies the test parameters for the test methods referred to in this standard. This European Standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes, e.g. CEN/TR 13801 [1]. NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 18. This standard applies to pipes and fittings, marked with “B”, which are intended to be used inside buildings and outside buildings fixed onto the wall. It applies to pipes and fittings, marked with “BD”, which are intended to be used for both inside buildings and buried in the ground within the building structure. This standard is applicable to PP pipes and fittings of the following types: — plain-ended, — with integral elastomeric ring seal socket, — for butt fusion joints, whereby the fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 4 EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements. NOTE 5 For information about the chemical resistance of PP, guidance is given in ISO/TR 10358 [3] and for rubber materials in ISO/TR 7620[4]. |
| Status |
Préliminaire
|
| Reference Document | |
| date of Availability (DAV) | |
| ICS | |
| A-Deviation(s) | |
| Special National Condition(s) |
Légal
| Directive(s) | |
|---|---|
| Mandate(s) | |
| Citation in OJEU |
Dates de mise en application
| date of Ratification (DOR) (1) | |
|---|---|
| date of Availability (DAV) (2) | |
| date of Announcement (DOA) (3) | |
| date of Publication (DOP) (4) | |
| date of Withdrawal (DOW) (5) |
Relations
| Supersedes |
EN 1451-1:2017/AC:2018
EN 1451-1:2017 |
|---|---|
| Superseded by |
(1) Date of ratification (dor) date when the Technical Board notes the approval of an EN (and HD for CENELEC), from which time the standard may be said to be approved
(2) Date of availability (dav) date when the definitive text in the official language versions of an approved CEN/CENELEC publication is distributed by the Central Secretariat
(3) Date of announcement (doa) latest date by which the existence of an EN (and HD for CENELEC), a TS or a CWA has to be announced at national level
(4) Date of publication (dop) latest date by which an EN has to be implemented at national level by publication of an identical national standard or by endorsement
(5) Date of withdrawal (dow) latest date by which national standards conflicting with an EN (and HD for CENELEC) have to be withdrawn
(6) This list of normative references is purely indicative. The only official list of normative reference is the list of the published standard.
In the case of undated standard, a link to the last dated version is provided.
In the case of series, a link to each standard identified in the series is provided.
We also invite you to check (via the website) whether corrigenda and/or amendments shall be read in conjunction with the main standard.