The European Committee for Standardization is one of three European Standardization Organizations (together with CENELEC and ETSI) that have been officially recognized by the European Union and by the European Free Trade Association (EFTA) as being responsible for developing and defining voluntary standards at European level.
- |
Reference | prEN ISO 11301-1 rev |
---|---|
Title | Titre manque Partie 1: Titre manque |
Work Item Number | 00155A16 |
Abstract/Scope | This document specifies requirements and test methods for pipes and fittings which are part of piping systems for the rehabilitation by means of renovation and trenchless replacement of underground gas supply networks. It is applicable to polyethylene (PE) pipes, fittings and assemblies, as manufactured and as installed. It is not applicable to the existing pipeline. It is applicable to technique families for renovation: — lining with continuous pipes; — lining with close-fit pipes; and technique families for trenchless replacement: — pipe bursting and pipe extraction; — horizontal directional drilling and impact moling. This document is applicable to: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex D, where all layers have the same MRS rating. Furthermore, when used with lining with continuous pipes and trenchless replacement this document is applicable to: — PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), as specified in Annex D. When used with lining with close-fit lining pipes, the lining pipe is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner. This document is applicable to jointing by means of butt fusion and electrofusion and to fabricated and injection-moulded fittings and mechanical connections of PE. This document is not applicable to push-fit jointed discrete pipes assembled as part of the trenchless installation process. |
Status |
En développement
|
Reference Document |
ISO 11301-1 (EQV)
|
date of Availability (DAV) | |
ICS | |
A-Deviation(s) | |
Special National Condition(s) |
Directive(s) | |
---|---|
Mandate(s) | |
Citation in OJEU |
date of Ratification (DOR) (1) | |
---|---|
date of Availability (DAV) (2) | |
date of Announcement (DOA) (3) | |
date of Publication (DOP) (4) | |
date of Withdrawal (DOW) (5) |
Supersedes |
EN ISO 21225-2:2018
EN ISO 21225-1:2018 EN ISO 11299-3:2018 EN ISO 11299-2:2018 EN ISO 11299-1:2018 |
---|---|
Superseded by |
(1) Date of ratification (dor) date when the Technical Board notes the approval of an EN (and HD for CENELEC), from which time the standard may be said to be approved
(2) Date of availability (dav) date when the definitive text in the official language versions of an approved CEN/CENELEC publication is distributed by the Central Secretariat
(3) Date of announcement (doa) latest date by which the existence of an EN (and HD for CENELEC), a TS or a CWA has to be announced at national level
(4) Date of publication (dop) latest date by which an EN has to be implemented at national level by publication of an identical national standard or by endorsement
(5) Date of withdrawal (dow) latest date by which national standards conflicting with an EN (and HD for CENELEC) have to be withdrawn
(6) This list of normative references is purely indicative. The only official list of normative reference is the list of the published standard.
In the case of undated standard, a link to the last dated version is provided.
In the case of series, a link to each standard identified in the series is provided.
We also invite you to check (via the website) whether corrigenda and/or amendments shall be read in conjunction with the main standard.