Cincinnati Test Systems’ Post

Which condition is most likely to cause erroneous conductivity readings despite correct calibration of a transmitter? A) Poor cable shielding from electrical noise B) Air bubbles trapped in the sensor cell C) Incorrect temperature compensation setting D) Fluctuating process flow rates Refer the below link for the Answer Troubleshooting of Conductivity Transmitter https://lnkd.in/gFVxDGXe

Treating control valve noise with fisher whisper technology.

There are many benefits to installing a dew point meter to monitor your compressed air system. Have you ever had a dryer fail in your compressed air system and ruin your production output? But you didn't notice until it was too late? The use of a dew point measuring instrument, called a dew point analyser or dew point meter for compressed air and gases, will help the user to operate a safe and reliable compressed air system by providing early warning alarms, not when things have already gotten worse. Talk to an expert: https://bitly.ws/3hjNd

Curious about back pressure regulators? This blog unravels the confusion surrounding their functionality and why they're more than just your average air regulator. Learn how these precision relief valves enhance safety and efficiency in your system. Read more: https://zurl.co/DNc8 #BackPressureRegulators #PrecisionReliefValves #RegulatorFunctionality

How to install a compressed air flow meter under pressure? Consumption and leakage rate measurement Compressed air demand profile Easy installation via ½” ball valve Usable from ½” to 12”(DN 300) https://lnkd.in/eVdsF3Xs https://lnkd.in/dYsxsSVE

Temperature measurement installations typically require a process shutdown for pipe modifications to install the thermowell. We have a solution for that. Read about it: http://emr.as/yi8b50Rx9Tu

Differential Transmitter in Action: This differential transmitter is connected to a closed tank, providing precise pressure measurements. In a closed tank system, the transmitter compares the pressure inside the tank with a reference pressure, usually atmospheric 🌬️. This enables accurate level measurements and ensures optimal control of fluid levels ⚙️. In contrast, an open tank differential transmitter works by comparing the pressure between the tank and the surrounding atmosphere 🌍, allowing for accurate monitoring of fluid levels in open systems. Both setups are crucial for maintaining safety and efficiency in industrial processes 🔧💡."

As General Checklist List the Essential Steps and precautions for Pre start and Starting up the Centrifugal Pumps ,What’s the things you Should be attention physically ? ✅ General centrifugal pump start up procedure:- Before pump start-up you must perform these tasks:- 1️⃣ Open the suction valve , do priming by venting all the air inside the suction line by opening any vent or even the PG vent till liquid coming out then close , now you confirm no air inside the system to reduce the chances of pump getting cavitation 2️⃣ Open any recirculation or cooling lines. 3️⃣ Fully close or partially open the discharge valve, depending on system conditions. 4️⃣ Start the driver. 5️⃣ Slowly open the discharge valve until the pump reaches the desired flow. 6️⃣ Check the pressure gauge to ensure that the pump quickly reaches the correct discharge pressure. 7️⃣ If the pump fail to reach the correct pressure, perform these steps: a. Stop the driver. b. Prime the pump again. c. Restart the driver. 8️⃣ Monitor the pump while it is operating. a. Check the pump for bearing temperature, vibration, and noise. b. If the pumps exceed normal levels, then shut down the pump immediately and correct the problem. 9️⃣ Repeat steps 7 and 6 until the pump runs properly.

🚨 Why a Portable Gas Leak Detector is Essential 🚨 Invisible gases like carbon monoxide are undetectable without the right tools. Portable gas detectors keep you safe by alerting you to hazardous levels, ensuring your team has time to take action. Keep your air safe, stay alert! Shop Now: https://lnkd.in/gpFj46E #GasDetection #SafetyFirst #PPE #PKSafety