CircuitBread’s Post

Smart - Fast - Digital (Ethernet APL used by iTEMP TMT86 transmitting temperature with profinet) by Endress Hauser. Integrated Functions 1. Push In Terminals 2. Diagnostic Monitoring a. Corrosion Monitoring of sensor wires b. Device Hardware Fault Recognition c. Sensor drift detections d. Sensor back up function

Change FTBx-3500 output power and attenuation | How-To Learn how to adjust output power and attenuation on your EXFO FTBx-3500 variable attenuator with ease. Using the Instrument Function tab, modify attenuation or output power using sliders, arrows, or the More Options button. Control light entry with the shutter function, toggling it open or closed as needed. Activate power tracking for automatic output power level monitoring. Optimize your testing process effortlessly with these features.

Have you heard about our newest instrument, the Moku Time & Frequency Analyzer? It replaces a photon counter, frequency counter, and DAQ, eliminating complex equipment management procedures needed for conventional hardware. 💡 Analyze lossless, real-time histograms ➡️ Configure event detector thresholds 🕝 Log raw event timestamps ⚡ Output a scaled voltage proportional to an interval Check it out: https://hubs.ly/Q02F6kcw0

Detectors are a critical part of analytical equipment. Learn about their power requirements and how high voltage power supplies enhance speed, accuracy, size and connectivity in our blog. https://bit.ly/425iQJO #AnalyticalEquipment #HighVoltagePower #DCDCConverters

Knick’s P27000 High-Voltage Universal Signal Conditioner is a powerful solution for Test & Measurement. With its continuous isolation specification of 1000 V, it can pair with data acquisition systems (DAQ’s) in applications where the level of voltage protection needed is beyond the capability of the acquisition hardware.  #highvoltage #electricalmeasurement

In REMdevice - Industrial Radio Controls we designed diagnostic tools to make installation and maintenance of our devices the easiest and the most reliable as possible. 𝐎𝐮𝐫 𝐌𝐨𝐧𝐢𝐭𝐨𝐫 𝐓𝐞𝐬𝐭𝐞𝐫 𝐢𝐬 𝐚 𝐬𝐞𝐥𝐟-𝐩𝐨𝐰𝐞𝐫𝐞𝐝 𝐝𝐢𝐬𝐩𝐥𝐚𝐲 𝐝𝐞𝐯𝐢𝐜𝐞 𝐭𝐨 𝐛𝐞 𝐜𝐨𝐧𝐧𝐞𝐜𝐭𝐞𝐝 𝐭𝐨 𝐭𝐡𝐞 𝐫𝐞𝐜𝐞𝐢𝐯𝐞𝐫, 𝐝𝐞𝐬𝐢𝐠𝐧𝐞𝐝 𝐭𝐨 𝐫𝐞𝐚𝐝 𝐭𝐡𝐞 𝐫𝐞𝐦𝐨𝐭𝐞 𝐜𝐨𝐧𝐭𝐫𝐨𝐥'𝐬 𝐨𝐩𝐞𝐫𝐚𝐭𝐢𝐧𝐠 𝐝𝐚𝐭𝐚. Information displayed: ✅Working frequency and channel used ✅Signal and interference levels ✅Number of starts and hours of operation ✅Number of up and down commands ✅Number of all other commands (T Series) ✅Relay operation diagnostics ✅Active commands

Did you know that regular calibration of your TLC Meter is required to ensure best accuracy in the field? Watch this video to see how easy it is: https://lnkd.in/gQtkQZ-8

Did you know that regular calibration of your TLC Meter is required to ensure best accuracy in the field? Watch this video to see how easy it is: https://lnkd.in/gQtkQZ-8

The AD-STC is an intrinsically safe barrier, designed with 1 or 2 channel(s) for reading 2-wire smart transmitters in hazardous areas. It reads data from hazardous areas through a 4 ~ 20 mA analog current signal via the HART protocol, which it then transfers to the safe area. After that, the collected data at the safe area is transmitted to the station, through a reproduced analog signal similar to the one in the hazardous area. Moreover, digital signals may be superimposed on the input signal in the hazardous or safe area, which it then transfers bi-directionally. The current and power consumption of the input is about 208 mA and 5W, respectively, and the power dissipation is less than 1W. The environmental conditions are -20 to +60 °C as an operation and -25 to +65 °C as storage temperature. The AD-STC is mounted on a sturdy 35 mm DIN mounting rail acc.

The AD-STC is an intrinsically safe barrier, designed with 1 or 2 channel(s) for reading 2-wire smart transmitters in hazardous areas. It reads data from hazardous areas through a 4 ~ 20 mA analog current signal via the HART protocol, which it then transfers to the safe area. After that, the collected data at the safe area is transmitted to the station, through a reproduced analog signal similar to the one in the hazardous area. Moreover, digital signals may be superimposed on the input signal in the hazardous or safe area, which it then transfers bi-directionally. The current and power consumption of the input is about 208 mA and 5W, respectively, and the power dissipation is less than 1W. The environmental conditions are -20 to +60 °C as an operation and -25 to +65 °C as storage temperature. The AD-STC is mounted on a sturdy 35 mm DIN mounting rail acc. HB SAGco