Friendcom America’s Post

Are you attending Digitalization in Oil and Gas in Houston this week? If so, be sure to stop by the Industrial LoRaWAN Solutions Hub (booth #101) to see the latest innovations that can take your operations to the next level. #DigitalizationOilandGas #DigiOil24

Monitor your energy efficiently with the Eastron Europe's SDM54 Meter that measure voltage, current, power, frequency, and more. Key features including up to 100A direct loads per phase, dual tariff options, and straightforward configuration via keypad. Also, Secure your settings with password protection. Read More : https://lnkd.in/eamp6Wym #EnergyMonitoring #SDM54 #EnergyManagement #SmartMeters #Innovation #Efficiency #SmartTechnology #EastronEurope

The Sensus Smart Gateway allows utilities to be better connected to their gas system in many ways. The interface application can be used to remotely monitor pressures, temperatures, levels, and switches. Here are some examples of how it can be applied to a system.

📌📌https://lnkd.in/ebn4PZuB 📌📌https://lnkd.in/gekTYGBu ✅✅#WirelessHART Application——#Thermal #Power #Plant—— Area 5. Other areas Other areas mainly include industrial water supply, demineralized water, refined reclaimed water, heat exchange station water, dust removal air compressor water, etc.; The WirelessHART protocol collects the domestic water flow in this area. The data is transmitted to the DCS in the central control room of the power plant and finally displayed in real-time on the smart water cloud platform. Number of applied products in this area: 💡Flowmeter (HART): 16 units 💡WirelessHART Adapter A1110: 16 units 💡WirelessHART Gateway G1100: 1 unit 💡WirelessHART Repeater R1100: 3 units 🤝🤝Contact me to get more information 📧📧fang.siqi@microcyber.cn

Large Water and Wastewater Utility Migrates from GE MDS 9710/SD9 Network to XetaWave A large metropolitan water and wastewater utility was experiencing failures within its communication system consisting of multiple networks with hundreds of GE MDS 9710/SD9 radios and PLCs. After 3 weeks of diagnosing the problem, they determined the source of the failure was a new SD9 radio. Since the GE MDS SD9 radios were operating in X710 mode, they decided to implement XetaWave radios which are interoperable with MDS radios. In just 10 minutes, they had XetaWave radios operational on their existing network. The end goal is to migrate from their existing legacy X710 serial network to an IP/Ethernet network. Since all XetaWave radios are software defined (SDR), this will simply require the change of a setting within their existing Xeta9 radios with no disruption to the operation of their networks. #XetaWave #X710 #MDSReplacement

With the use case 'Monitoring of Grid Connection Point', the meter reading can be communicated. It is not defined how often the data must be transmitted. The transmission rate depends on the characteristics of the meter. The following empirical formula may help: If the measurement intervals need to be significantly less than one second, faster sub-meters are used. With an SMGW, measurement intervals of only about one second are possible. #SMGW #smartmeter #smartgrid #gridconnection

📌📌https://lnkd.in/eKSx4jz8 📌📌https://lnkd.in/gqS4mYFR ✅✅#WirelessHART Application——#Thermal #Power #Plant—— Area 5. Other areas Other areas mainly include industrial water supply, demineralized water, refined reclaimed water, heat exchange station water, dust removal air compressor water, etc.; The WirelessHART protocol collects the domestic water flow in this area. The data is transmitted to the DCS in the central control room of the power plant and finally displayed in real-time on the smart water cloud platform. Number of applied products in this area: 💡Flowmeter (HART): 16 units 💡WirelessHART Adapter A1110: 16 units 💡WirelessHART Gateway G1100: 1 unit 💡WirelessHART Repeater R1100: 3 units 🤝🤝Contact me to get more information 📧📧fang.siqi@microcyber.cn

The OrionMeter LA-IP #LoRaWAN radiomodem is designed to count pulses, with subsequent accumulation and transmission of information to the LoRaWAN® network. The pulse counter can be used to collect data from #utility meters and #industrial equipment with pulse output, such as water meters, electricity meters, heat meters, flow meters, etc. Main parameters: LoRaWAN® v1.0.3 Class A; Ultra-low power consumption; Fast installation and deployment; Uses non-volatile memory to store data; EasyTool technology allows you to configure the device remotely; Transmission range – up to 15 km; The service life with BatteryCare® technology is up to 10 years.

About LoRaWAN Pulse Counter

Myth or fact... 💭 Test your knowledge of fact and fiction as we debunk some common misconceptions about gas detection. Swipe to reveal the answer to: sensors do not need to be replaced once they’re in the field. ➡️ Tap to learn more about gas sensor life expectancy: https://buff.ly/3RDO33H #GasDetection | #MythOrFact | #CETCI