Sullivan-Palatek, Inc.’s Post

The circuit of the oil press keeps tripping after being connected If the circuit of the oil press keeps tripping after being connected, it may be caused by the following reasons: The load is too large: Check whether the rated current of the circuit meets the requirements of the oil press. If it is not enough, you need to upgrade the circuit or replace the oil press. Short circuit in the circuit: You can check whether the circuit is damaged, worn, or has poor plug contact. Circuit failure: Check whether the internal circuit of the oil press is normal and whether there is damage to capacitors, resistors and other components. Ground wire failure: The ground wire of the oil press may be faulty, causing the circuit to trip; whether the ground wire is firmly connected or damaged, etc. In short, if the oil press circuit keeps tripping after being connected, you need to carefully check the circuit, the internal circuit of the oil press machine, the grounding wire and other problems, and then repair it after finding the specific cause. At the same time, to ensure safety, it is recommended to seek professional help. #hrdralicoilpress #screwoilpress #oilpressmachine #coldpress #hotpress #copraoilpress #oilrefinery #refineryequipment #palmoilpress #musrardseedsoil

Rotary Valve / Air Lock Basically, it ensures that the dosage and transfer of raw materials—both granular and powder—from the feeding point to the discharge point are done in a controlled manner. Similar to pneumatic air conveying systems, it prevents the conveying air from escaping to the feeding point when the material is being transferred from the feeding bunkers to the pipeline. #rotaryvalve #rotaryfeeders #rotaryairlock #processengineering #airlockvalves

Rotary Valve / Air Lock Basically, it ensures that the dosage and transfer of raw materials—both granular and powder—from the feeding point to the discharge point are done in a controlled manner. Similar to pneumatic air conveying systems, it prevents the conveying air from escaping to the feeding point when the material is being transferred from the feeding bunkers to the pipeline. #rotaryvalve #rotaryfeeders #rotaryairlock #processengineering #airlockvalves

Rotary Valve / Air Lock Basically, it ensures that the dosage and transfer of raw materials—both granular and powder—from the feeding point to the discharge point are done in a controlled manner. Similar to pneumatic air conveying systems, it prevents the conveying air from escaping to the feeding point when the material is being transferred from the feeding bunkers to the pipeline. #rotaryvalve #rotaryfeeders #rotaryairlock #processengineering #airlockvalves

How does a double-skin liner differ from a normal liner? Double-skin lining provides multiple layers of protection including a corrosion-resistant coating and a vacuum that enables 24/7 monitoring of the storage tanks integrity. #storagetanks #storageterminals #corrosionresistance #oilandgas

Our Overpressure Specialists love that Curtiss-Wright Valves Division's Farris 3800 series pilot-operated relief valves do things conventional spring-operated relief valves cannot! The 3800 is perfect if your application requires you to operate beyond 90% of your set pressure, you have high variable back pressure, you need a full bore PRV for your required capacity, or you want maximum seat tightness as pressure rises. Both the Snap-Acting and Modulating pilot controls allow for bubble-tight operation close to set pressure and are unaffected by back pressure. In addition to robust overpressure protection, the 3800 Series allows maximum product throughput, increased system profitability, and reduced fugitive emissions. The modulating pilot control responds gradually and proportionately rises in over pressure, minimizing product losses and reducing reaction forces when the flow requirement is below the maximum rated flow of the valve. The new CVS (Clean Vacuum Service) modulating pilot control option allows for the 3800 series to successfully operate in applications that see negative process pressure where standards pilot operated valves would fail! For more information: https://hubs.ly/Q02F3xFm0 Chat with an AWC Overpressure Specialist about your PRV needs: https://hubs.ly/Q02F3jGy0 #curtisswright #farris

Send a ZX200-3 control valve, part number 4628664 to a Mexican customer. The main control valve, also known as the main valve, is used to provide the pressure oil discharged by the pump to each actuator according to the operator's instructions, enabling the excavator to complete various actions. #mainvalve #Válvuladecontrol #Rotaryvalve #Cannonvalve #pressure #Atlas

💡Did you know?📣📣📣📣 Higher suction tank elevations can indeed exert more pressure on pump seals and glands, potentially leading to sealing issues and increased wear over time. This additional pressure can challenge the integrity of the seals, increasing the likelihood of leaks and reducing the lifespan of the pump components. Proper maintenance and monitoring are essential to address any issues and ensure reliable pump operation. #SuctionTankPressure #PumpPerformance #FluidMechanics #EngineeringSolutions #PumpMaintenance #FluidDynamics #MechanicalEngineering #ProcessEngineering #IndustrialPumps #MaintenanceTips

Leaks are a significant source of wasted energy in a compressed air system, often wasting as much as 20%-30% of the compressor’s output. Compressed air leaks can also contribute to problems with system operations, including: • Fluctuating system pressure, which can cause air tools and other air-operated equipment to function less efficiently, possibly affecting production • Excess compressor capacity, resulting in higher than necessary costs • Decreased service life and increased maintenance of supply equipment (including the compressor package) due to unnecessary cycling and increased run time. Although leaks can occur in any part of the system, the most common problem areas are couplings, hoses, tubes, fittings, pipe joints, quick disconnects, FRLs (filter, regulator, and lubricator), Air Blow Gun and point-of-use devices. Interested in Pneumatic products which are leak free - Air Blow Gun, Quick Release Coupling, Tubes etc, Hose Reel etc. , contact us on satish.raikar@cejn.com

Many heat exchanger shells are either insulated or come with a fire protection coating. Therefore, it is not uncommon to see corrosion mechanisms at play: moisture is often trapped between the steel (outer diameter) and the insulation/fireproofing material, leading to what the industry calls “Corrosion Under Insulation”. The threat can be significant because corrosion is impossible to detect unless the asset is taken out of service, entire insulation/fireproofing removed, and visual inspection performed. Eddyfi Technologies offers a solution that allows detecting corrosion in this scenario, without having to disrupt operations. Lyft® is a Pulsed Eddy Current (PEC) solution capable of locating generalized corrosion through insulation/coating. #ndt #ndtinspection #ndtequipment https://lnkd.in/gCvyubKk