OGI Process Equipment’s Post

#DidYouKnow? Water cooling towers need to be handled with as much care as just about any other important appliance as they are the heart of a building’s mechanical system. #havc #hvacmaintenance #hvacrepair #outdoors

The general purpose of hall ventilation is to prevent moisture from damaging the building or process equipment as well as to remove and exhaust heat and moisture loads and airborne impurities. During the winter season, the building is heated to prevent any damage to buildings and equipment caused by condensation and freezing. The hall ventilation also enables a healthy and comfortable working climate for the operators. A typical way to ventilate the machine hall is to supply clean air to the working zones at low speed. The supply air ventilates working zones without a draught. Due to the thermal loads from the process and its equipment, the supply air temperature increases, rising toward the machine hall ceiling from where it is released. Temperature, humidity, and concentration of impurities are always higher at the upper parts of the machine hall than the lower parts. Machine hall ventilation audit focuses on air and water balance measurements, machine hall temperature and humidity levels, misting around the paper machine’s wet end, hood air and water balance calculations, hood zero level along with the water and humidity load to the machine hall. Fans, hoods, ducts, valves, hatches, heat recovery systems and auxiliary equipment are all visually inspected. If you want your machine checked, contact us! https://lnkd.in/dgCcBKbx #energyefficiency #auditservices #optimization #papermaking #pulpandpaper #runtech #leanonus

Box Type Air-cooled Chiller Our Box Type Air-Cooled Chiller provides an answer to all your “chill” problems. Whether it is a storage room or your concrete, this chiller cools down the temperature of required things like food or other materials. https://buff.ly/3F7jdIE #refrigerationsystems #coldroomstorage #Compressors #AirCooledCondensingUnits #WaterCooledCondensingUnits

Box Type Air-cooled Chiller Our Box Type Air-Cooled Chiller provides an answer to all your “chill” problems. Whether it is a storage room or your concrete, this chiller cools down the temperature of required things like food or other materials. https://buff.ly/3F7jdIE #refrigerationsystems #coldroomstorage #Compressors #AirCooledCondensingUnits #WaterCooledCondensingUnits

What is the fill in a cooling tower? #coolingtowers #coolingsystem #PVCfills #filmfiller #closedcoolingtower #PPFilling The cooling tower is a cooling device, which makes the hot water in the tower be cooled mainly by the evaporative cooling of water. To make full use of water resources, reduce the load of the urban tap water supply network, and reduce the operating cost, cooling water is treated by the cooling tower and recycled. "Fill" is a medium that is used in cooling towers to increase the surface area available for the water. In a cooling tower, the important is cooling tower fill. Fill is a plastic sheet used in cooling towers to build the more surface region of the tower. If we want to expand the surface, we need to consider into making more contact with water and fills, so that water will have more surface area in the cooling tower fill. Cooling tower fills make hot water have much more surface area with sheet and air and the medium of tremendously extended film fills so that hot water is cooled quickly. After being cooled the water is flowed into a water container from which it is pumped again to cool other hot water, and the warm air leaves the fill and releases from the above of the cooling towers, and like this Continuously cooling air from the bottom and release warm air from above to keep cooling tower cooling hot water continuously, to reduce the load of urban tap water supply network, and reduce the operating cost, So that we could make full use of water resources. The filler is the most important part of the cooling tower, and its efficiency depends on the extent to which the cooling water and air are fully in contact with the filler. Filler temperature 50 °C ~ 68 °C, anti-aging, excellent performance, anti-ultraviolet, long life. Cooling tower fill should be made to have more contact with water and fills, and longest time as possible. Fill allows the water to form thin flowing sheets to expose as much water surface area as possible to the interacting flow.

Did you know that a water heater replacement can save you money on your energy bills? Let Pratt Plumbing and Heating help you find the perfect replacement! #WaterHeaterReplacement #EnergyEfficiency

Why are PU Panels used in Cold Rooms? Discover why PU (Polyurethane) panels are the top choice for cold room insulation. Learn about their superior thermal insulation, energy efficiency, moisture resistance, and ease of installation. Perfect for maintaining low temperatures and reducing operational costs, PU panels offer durability and long-lasting performance. Watch to find out more!   #coldroom #pupanels #pufpanels #coldroompanels #coldstorage #insulatedpanels #sandwichpanels

Did you know that a water heater replacement can save you money on your energy bills? Let Pratt Plumbing and Heating help you find the perfect replacement! #WaterHeaterReplacement #EnergyEfficiency

Here in this blog, we will share top plumbing tips to reduce the cost and increase efficiency in household chores. Moreover, you can also save on energy and water bills. So what’s the wait let’s get started🔍 #VGvalogin #valve #pipingsystem

Are you tired of constantly adjusting your thermostat? Let Pratt Plumbing and Heating install a programmable thermostat for you. #Thermostat #PrattPlumbingandHeating