National Heat Transfer LLC’s Post

Capable of providing heating using either hot water or refrigerant, they are typically supplied with low temperature hot water (LTHW). They can function using much lower grade hot water (i.e. < 550C flow) than that traditionally employed and are therefore capable providing heating in conjunction with condensing boilers or heat pumps. https://lnkd.in/eKAy3MMd #fancoilunit

The all-in-one water pressure booster, SCALA2, can be installed in 5 simple steps: 1️⃣ Connect the pipes. The inlet and outlet connections are adjustable by up +/- 5°, making the installation even easier. 2️⃣ Prime the pump: the large priming plug enables you to fill water quickly and easily. You must fill the pump with a minimum of 1.7 liters of water. 3️⃣ Plug the pump into a power outlet and start the pump. The default pressure setting is 3 bar (43 psi). 4️⃣ Adjust the tank precharge pressure according to the setpoint. 5️⃣ And for countries like the US, make sure there is an expansion tank (not to be confused with the tank inside the pump) installed in the system and that it is pre charged before installing into the system. More information❔ Please watch the installation video on the product page or look for the guide on the packaging. 👉 http://spr.ly/6049jS2N5 #WaterPressure #WaterBoost #PressureBoosting #WaterPump #GrundfosSCALA2 #WaterBoosting #Boosting #ConstantPressure

Shell And Tube Water-Cooled Evaporator Condenser will be designed based on the operating conditions as belows: Inlet water temp.: tW1=30℃ Outlet water temp.:tW2=35℃ Condensing temp.: 40℃ Cooling water flow rate:1.5〜2.5m/s

Do you know how air is distributed with hot water baseboard systems? The water is heated by a boiler, and this is piped to “fin-tube” baseboard units that are mounted along walls. The fins increase the surface area of heat dissipation, making the unit more efficient.

The all-in-one water pressure booster, SCALA2, can be installed in 4 simple steps: 1️⃣ Connect the pipes. The inlet and outlet connections are adjustable by up +/- 5°, making the installation even easier. 2️⃣ Prime the pump: the large priming plug enables you to fill water quickly and easily. You must fill the pump with a minimum of 1.7 liters of water. 3️⃣ Plug the pump into a power outlet and start the pump. The default pressure setting is 3 bar (43 psi). 4️⃣ Adjust the tank precharge pressure according to the setpoint. More information❔ Please watch the installation video on the product page or look for the guide on the packaging. 👉 http://spr.ly/60405N5tK #WaterPressure #WaterBoost #PressureBoosting #WaterPump #GrundfosSCALA2 #WaterBoosting #Boosting

Clogged condensate drain lines is one of the most common, yet avoidable air conditioning failures. It has the potential to cause serious property damage(especially when a/c units are in the ceiling above expensive furniture or equipment). Remind your air conditioning maintenance vendors to… 1) Clean your evaporator condensate pans. 2) Confirm condensate pump is free of sludge and operational 3) Vacuum out your drain lines. #facilitiesmanagement #airconditioningmaintenance

The all-in-one water pressure booster, SCALA2, can be installed in 4 simple steps: 1️⃣ Connect the pipes. The inlet and outlet connections are adjustable by up +/- 5°, making the installation even easier. 2️⃣ Prime the pump: the large priming plug enables you to fill water quickly and easily. You must fill the pump with a minimum of 1.7 liters of water. 3️⃣ Plug the pump into a power outlet and start the pump. The default pressure setting is 3 bar (43 psi). 4️⃣ Adjust the tank precharge pressure according to the setpoint. More information❔ Please watch the installation video on the product page or look for the guide on the packaging. 👉 http://spr.ly/6045eehVx #WaterPressure #WaterBoost #PressureBoosting #WaterPump #GrundfosSCALA2 #WaterBoosting #Boosting

Avoid These Five Mistakes During Water Heater Installation: https://zurl.co/Le0j

The all-in-one water pressure booster, SCALA2, can be installed in 4 simple steps: 1️⃣ Connect the pipes. The inlet and outlet connections are adjustable by up +/- 5°, making the installation even easier. 2️⃣ Prime the pump: the large priming plug enables you to fill water quickly and easily. You must fill the pump with a minimum of 1.7 liters of water. 3️⃣ Plug the pump into a power outlet and start the pump. The default pressure setting is 3 bar (43 psi). 4️⃣ Adjust the tank precharge pressure according to the setpoint. More information❔ Please watch the installation video on the product page or look for the guide on the packaging. 👉 http://spr.ly/6044dkgzy #WaterPressure #WaterBoost #PressureBoosting #WaterPump #GrundfosSCALA2 #WaterBoosting #Boosting

The all-in-one water pressure booster, SCALA2, can be installed in 4 simple steps: 1️⃣ Connect the pipes. The inlet and outlet connections are adjustable by up +/- 5°, making the installation even easier. 2️⃣ Prime the pump: the large priming plug enables you to fill water quickly and easily. You must fill the pump with a minimum of 1.7 liters of water. 3️⃣ Plug the pump into a power outlet and start the pump. The default pressure setting is 3 bar (43 psi). 4️⃣ Adjust the tank precharge pressure according to the setpoint. More information❔ Please watch the installation video on the product page or look for the guide on the packaging. 👉 http://spr.ly/6048jSX5q #WaterPressure #WaterBoost #PressureBoosting #WaterPump #GrundfosSCALA2 #WaterBoosting #Boosting