Our most popular product just gets the job done. Our all-welded one piece 12-GA steel body offers the strength you need to handle the abuse in high traffic areas. With all the different combinations we offer you can securely store the gear that matters to you with Strong Hold products.
Strong Hold’s Post
More Relevant Posts
-
#Discussed About #Hotvulcanizingmachine #Manufacturer/Origin/Model: Bai- Ott/China/RIT-1000 #Belt width: 1000 mm max #Angle of junction : 22 degree #Service pressure :6 bar #Quantity of folds of belts : 3 minimum #Belt thickness :7 mm minimum #Temperature range of belt: 0 to 200°C #Type of belt: ISO 340/284 #Power supply: 220/380V+/-10% 3 phases
-
-
Tapered roller bearing installation technology. The installation process from raw material to finished product. In the video is the product explanation, we use the machine to install the cone roller in the retainer. The machine will place each roller in the cage, and then place the inner ring of the cone roller for fixing, which is the installation process. Simple and fun, with a good mechanical installation speed, is a good experience. 👨🔧 The technical department told us that when installing such bearings, we should pay attention to hand gloves to avoid long-term rust affecting subsequent use. I think he is very professional. #Bearing#YK #installationprocedure #Auto manufacturing parts
-
O-Ring Cord (also known as o-ring strip or o-ring rope) is a rubber cord seal with a circular cross-section. It can be directly used on a sealing groove to prevent fluid or gas from leaking or cut the required length and use specific glue to DIY join two ends to form the needed standard o-ring. The rubber cord is usually stretch-formed, so its manufacturing time is short. It can be cut to 1-meter length or rolled into 100-meter or longer for easy packing and transportation.
-
-
Very good info, the cap is the final seal
Schrader cores are a "one and done" due to plastic deformation, (permanent deformation) of the sealing surface to the valve body. That is why they are not seated from the factory in many new access fittings. The core is also part of the system that included the gasketed cap. I could not post the video in the comments so here it is. https://lnkd.in/d33didJE Edward Louie, James M.
-
therefore, the schrader must be fitted with a shut-off valve
Schrader cores are a "one and done" due to plastic deformation, (permanent deformation) of the sealing surface to the valve body. That is why they are not seated from the factory in many new access fittings. The core is also part of the system that included the gasketed cap. I could not post the video in the comments so here it is. https://lnkd.in/d33didJE Edward Louie, James M.
-
Installing the best or the worst performing wear plate, takes exactly the same amount of time. Often when you install the lowest price wear plate, it quickly becomes apparent you will be forced to replace it once again in the not-too-distant-future. This means you have to purchase more steel, un-install and re-install it all over again. What Have You Gained Using Low Dollar Steel? Nothing... https://lnkd.in/gpen7wbr
-
-
Simple but important piece of item.without this piece of engineering Refrigeration could hv been an issue with leaking.
Schrader cores are a "one and done" due to plastic deformation, (permanent deformation) of the sealing surface to the valve body. That is why they are not seated from the factory in many new access fittings. The core is also part of the system that included the gasketed cap. I could not post the video in the comments so here it is. https://lnkd.in/d33didJE Edward Louie, James M.
-
#PTFEsewingthread #FilterBagProduction #Filtration Brief introduction of PTFE sewing thread from FILMEDIA GROUP Advantages of our PTFE sewing thread: 1. The continuous high temperature resistance of PTFE itself can reach 260 ℃ 2. PTFE has strong corrosion resistance and can adapt to harsh working conditions 3. Superior tensile strength Several reasons to choose PTFE sewing thread produced by FILMEDIA 1. We accept customized PTFE thread in various colors 2. We can produce various specs including 1200D, 1500D, 1800D and 2400D, etc 3. As for the common PTFE thread specification 1200D, the weight of our one bobbin is 800 - 1000 g, and the length of each bobbin is about 7500 m. 4. We use neutral carton packaging and then fix it on a plywood pallet to ensure the integrity of the product during transportation
-
-
Did you know about the Tool Release (TR) option for the BFM fittings? If you are installing a BFM sleeve next to moving machinery, you need to consider the risk of the sleeve being removed and an operator being exposed to danger. The BFM tool release sleeve has a much stiffer snap-band which is very difficult to remove by hand and instead requires a specific tool to release the sleeve. As well as the TR sleeving option, there are options such as internal grids and external guarding which can be considered.
-
-
Do you need two different sized V-Guides on your conveyor belt? Our skilled fabricators can easily make one for you. Don't believe us? Watch as Sean welds two K17 and two K22 Notched PU guides on to our Pure 20 Black TPU belt. It's a pretty straightforward fabrication: mark your V-Guide locations, weld the V-Guides on each side, flex and kiss your bicep, trim off the excess V-Guide, and then grind the V-Guide joint and put the notches back in. Fabricator's Note: the bicep flex is optional, but makes a great video. 😂 #conveyor #conveyors #conveyorbelt #conveyorbelts #conveyorsystem #conveyorsystems #conveyorsolutions #bandastransportadoras #beltingmadeeasy
